RTF Kit GEPRC TinyGO

GEPRC TinyGO is a ready-to-use FPV kit for hobby, learning, and training flights indoors or outdoors, provided safe flight conditions are followed. The kit includes a drone, controller, FPV goggles, charger, batteries, and a transport bag.

TinyGO is available in several versions, including an indoor flight version and a 4K version. The 4K version supports video recording up to 4K, provided the corresponding camera settings and memory card are used.

The kit includes FPV goggles with a resolution of 800x480 pixels and a TinyRadio ELRS 2.4G remote controller. The controller supports 8 channels and is powered by two 18650 batteries, which are not included. Before use, it is necessary to check battery compatibility, frequency settings, and the drone configuration.

TinyGO is charged using the included charger via USB or Type-C. The charger can also be powered from a compatible power bank, provided the output parameters are suitable.

The drone frame has a protective design with damping EVA foam around the perimeter. This design is used in whoop drones for training flights and reducing the risk of damage to elements during contact with obstacles.

Features

• TinyGO is suitable for learning and training flights indoors and outdoors, provided there is a safe space.
• Approximate flight time is over 6 minutes according to the manufacturer. Actual time depends on the battery, settings, flight style, and conditions of use.
• The TAKER F411 8Bit 12A FC flight controller is used.
• The drone design does not block the view with propellers in the video frame in the standard configuration.
• The FPV goggles have a resolution of 800x480 pixels and a 5.8G receiver.
• The ready-to-use kit includes a GEPRC bag for storage and transportation.
• Versions: standard version for training and 4K version for video recording with supported camera modes.

Compatibility
Before use, it is necessary to check the drone’s compatibility with batteries, charger, controller, FPV goggles, frequency settings, firmware, and operating conditions. Use of FPV equipment must comply with local rules and permitted parameters for radio frequency equipment.

TinyGO 4K version specifications
Camera: Loris 4K
Sensor: 1/2.7" CMOS
Horizontal resolution: 800TVL
Signal system: NTSC/PAL
Video resolution: 1080P@60fps / 1080P@90fps / 2.7K/60FPS / 4K/30FPS / 4K/60FPS according to the manufacturer
Power supply: DC 4.5-20 V
FOV for FPV: 165°
FOV for recording: 170°
Light sensitivity: 0.01Lux
Lens: 1.8 mm
Power current: 380 mA at 5 V / 160 mA at 12 V
OSD screen menu: yes, with voltage display support
Video format: MOV
Audio: supported
Electronic shutter: PAL: 1/50-100,000, NTSC: 1/60-100,100
Video output: CVBS

Controller
Model: TinyRadio ELRS 2.4G
Transmitter frequency: 2.4 GHz
Number of channels: 8
Transmission power: less than 500 mW
Antenna interface: SMA
Low-voltage alert: less than 6.6 V
Power supply: 2 x 18650 batteries, not included

FPV goggles
Resolution: 800x480 pixels
Screen size: 4.3 inches
Overall size: 155 mm x 144 mm x 113 mm
Built-in battery: 3.7 V / 2000 mAh
Approximate operating time: up to 2.5 hours according to the manufacturer
Weight: 314.6 g

Battery
Type: LiHV 1S1P
Capacity: 530 mAh
Voltage: 4.35 V
Manufacturer-stated discharge rating: 90C
Size: 61 mm x 16.7 mm x 7 mm
Weight: 12.7 g
Connector type: PH2.0

Charger
Input voltage: 5 V via USB or Type-C
Fully charged battery voltage: 4.35 V
Output current: 500 mA
Charging support: up to 2 1S HV LiPo 4.35 V batteries with PH2.0/GNB27 connectors, provided they are compatible

Package contents

1 x TinyGO TinyWhoop
1 x TinyRadio ELRS 2.4G controller
1 x GEPRC FPV RG1 FPV goggles
1 x GEPRC 1S LiHV 4.35 V charger
4 x GEPRC LiHV 4.35 V 90C battery
1 x Battery strap
4 x Gemfan 1636*4 propellers (pair)
1 x GEPRC transport bag
1 x Screwdriver